Swap PEPE to HYPE in three steps without creating an account. You see an estimated amount before you send, the exchange runs automatically once your deposit confirms, and the HYPE goes straight to the wallet address you enter.
Enter the amount of Pepe you want to swap in the widget above. It shows an estimate of the Hyperliquid (HyperEVM) you will receive on the HyperEVM network at the current floating rate, with the payout network fee already taken into account.
Paste your HYPE wallet address and check it twice, because blockchain transfers cannot be reversed. If the coin needs a memo or destination tag, a field for it appears. xswap.to never asks for your private keys.
Confirm the order and send your PEPE to the one-time deposit address on the Ethereum network. Once the deposit confirms, the swap runs automatically and the HYPE is sent to your wallet. The order page shows every stage.
Swapping Pepe (PEPE) for Hyperliquid (HyperEVM) (HYPE) here takes one transfer from your wallet: no exchange account, no balance to deposit and no withdrawal queue. You choose the receiving address, and the HYPE goes there once the swap completes.
Rates are floating, so the amount shown is an estimate that can shift slightly while your Pepe deposit confirms on Ethereum. The payout is sent on HyperEVM, so check that your Hyperliquid (HyperEVM) address belongs to that network before you confirm.
Refreshed hourly. The widget shows the live estimate.
416472 PEPE
≈
0.0136282 HYPE
At the latest hourly update, 416472 PEPE converts to about 0.0136282 HYPE. The figure comes from the floating rate and already allows for the payout network fee. Rates move, so the widget recalculates the estimate when you enter your own amount, and no account or registration is needed to swap.
PEPE token contract:
0x6982508145454Ce325dDbE47a25d4ec3d2311933
Approximate exchange rates between these assets, refreshed hourly
Your PEPE leaves Ethereum as an ERC-20 token, and native HYPE arrives on HyperEVM at a 0x address you control. There is no account to open and no email to hand over. Most people who swap PEPE to HYPE are moving meme-coin holdings into the Hyperliquid ecosystem, where HYPE is the native token of Hyperliquid's own blockchain and the coin you need to pay gas for anything you do on HyperEVM.
Pepe (PEPE) is a meme token on Ethereum at contract 0x6982508145454Ce325dDbE47a25d4ec3d2311933, so moving it costs gas in ETH, not PEPE. HyperEVM is the EVM-compatible chain that runs on Hyperliquid. Both sides use 0x addresses, yet this is still a cross-chain swap: the payout lands on HyperEVM, which is separate from the HyperCore trading balances you see in the Hyperliquid app. Neither side needs a memo.
A floating-rate estimate appears in the widget before you send, and the HyperEVM network fee for delivering your HYPE is already subtracted from it. Ethereum adds a block every 12 seconds, and the exchange starts once your PEPE deposit is confirmed there. Meme tokens can swing hard within minutes, so the final HYPE figure may land a little away from the quote. Your order page shows live status and a transaction ID to keep in case you need support.
From live exchange data, refreshed hourly.
| You send | You receive | |
|---|---|---|
| Asset | PEPE | Hyperliquid (HyperEVM) (HYPE) |
| Network | Ethereum | HyperEVM |
| Type | ERC-20 token | Native coin |
| Contract | 0x698250…311933 |
- |
| Memo / tag | Not needed | Not needed |
| Route | Cross-chain: Ethereum to HyperEVM | |
| Rate | Floating, estimate shown before you send | |
| Minimum to send | 396639.0836607 PEPE | |
| Account / ID | Not needed to start a swap | |
PEPE is an ERC-20 token, and every transfer on Ethereum pays its gas in ETH. A wallet holding only PEPE cannot push the deposit through. Top up a small amount of ETH first, and check the gas estimate in your wallet before confirming.
Not by itself. The payout goes to your address on HyperEVM, which is separate from the HyperCore balances used for trading on Hyperliquid. If you want to trade with it, transfer it from HyperEVM to HyperCore inside Hyperliquid after the swap finishes.
In most cases you can, because HyperEVM uses the same 0x address format as Ethereum and the same key controls that address on both chains. Add HyperEVM to the wallet so the balance shows up. Avoid pasting an exchange deposit address unless that exchange confirms it credits HYPE sent on HyperEVM.
Only ERC-20 PEPE on Ethereum mainnet works for this order. Tokens sent from another network to the deposit address are on the wrong chain for the order and can be lost. Bridge them back to Ethereum yourself first if that is where they sit.
Swaps here use a floating rate, so the quote is an estimate taken when you created the order. PEPE and HYPE both move quickly, and any change before your deposit confirms flows into the payout. The network fee for sending HYPE was already inside the estimate.
Open the order page first, since it shows whether the swap is waiting, confirming, exchanging or sending. Recent orders are saved in your browser and listed on the Track Order page. If a stage looks stuck, contact support on Telegram at @xswap_to and include the transaction ID.
