Swap XMR to LINK in three steps without creating an account. You see an estimated amount before you send, the exchange runs automatically once your deposit confirms, and the LINK goes straight to the wallet address you enter.
Enter the amount of Monero you want to swap in the widget above. It shows an estimate of the Chainlink you will receive on the Ethereum network at the current floating rate, with the payout network fee already taken into account.
Paste your LINK (Ethereum) wallet address and check it twice, because blockchain transfers cannot be reversed. If the coin needs a memo or destination tag, a field for it appears. xswap.to never asks for your private keys.
Confirm the order and send your XMR to the one-time deposit address on the Monero network. Once the deposit confirms, the swap runs automatically and the LINK is sent to your wallet. The order page shows every stage.
Swapping Monero (XMR) for Chainlink (LINK) here takes one transfer from your wallet: no exchange account, no balance to deposit and no withdrawal queue. You choose the receiving address, and the LINK goes there once the swap completes.
Rates are floating, so the amount shown is an estimate that can shift slightly while your Monero deposit confirms on Monero. The payout is sent on Ethereum, so check that your Chainlink address belongs to that network before you confirm.
Refreshed hourly. The widget shows the live estimate.
1 XMR
≈
54.945663 LINK
At the latest hourly update, 1 XMR converts to about 54.945663 LINK. The figure comes from the floating rate and already allows for the payout network fee. Rates move, so the widget recalculates the estimate when you enter your own amount, and no account or registration is needed to swap.
LINK token contract:
0x514910771af9ca656af840dff83e8264ecf986ca
Approximate exchange rates between these assets, refreshed hourly
As of Nov 4, 2026 14:52 UTC, 1 XMR is worth about $632.69 and 1 LINK about $10.64, so 1 XMR converts to roughly 54.945663 LINK. These figures move with the market, and the widget shows the live estimate before you confirm.
You send Monero (XMR) from your own wallet on the Monero network and receive Chainlink (LINK) as an ERC-20 token at an Ethereum address you control. No account or email is involved: you paste the 0x address, get a one-time XMR deposit address and send. People often swap XMR to LINK when they keep savings in Monero but want a widely listed Ethereum token to hold in a hardware wallet or use in Ethereum apps.
Monero hides the sender, receiver and amount of every transfer with ring signatures, stealth addresses and RingCT, and miners secure it with proof of work. Chainlink is an oracle network that feeds outside data to smart contracts, and LINK is the token used to pay its node operators. The two assets sit on different chains, so the payout needs a standard 0x Ethereum address. No memo is needed, but moving the LINK later will cost ETH for gas.
Before you send, the widget shows a floating-rate estimate of the LINK you will get, with the Ethereum network fee for the payout already taken out. If the market moves while your Monero deposit confirms, the final figure can shift a little. Monero targets a block about every two minutes and Ethereum produces one every 12 seconds, so most of the wait is on the XMR side. Your order page shows each stage and a transaction ID.
From live exchange data, refreshed hourly.
| You send | You receive | |
|---|---|---|
| Asset | Monero (XMR) | Chainlink (LINK) |
| Network | Monero | Ethereum |
| Type | Native coin | ERC-20 token |
| Contract | - | 0x514910…f986ca |
| Memo / tag | Not needed | Not needed |
| Route | Cross-chain: Monero to Ethereum | |
| Rate | Floating, estimate shown before you send | |
| Minimum to send | 0.0115876 XMR | |
| Account / ID | Not needed to start a swap | |
On Ethereum, as the ERC-20 token at contract 0x514910771af9ca656af840dff83e8264ecf986ca. That is the default for this page. LINK is also listed on BNB Smart Chain, Arbitrum One and Polygon PoS, and you can pick one of those in the coin selector before creating the order.
No, receiving the LINK costs you nothing extra, because the Ethereum network fee for the payout is deducted from the amount. You will need ETH later to send, swap or stake that LINK, so a small balance at the same address saves trouble.
Only on the Monero side. Your XMR transfer to the deposit address uses Monero's built-in privacy, but the LINK payout is an ordinary Ethereum transaction, so the receiving address and amount are visible on any block explorer. Use a fresh address if you want to keep that wallet separate from your other activity.
Rates are floating, so the estimate reflects the market when you created the order. If the price of XMR or LINK moves while the Monero deposit is confirming, the payout follows the rate at exchange time. That movement can go in your favor too.
Keep the Monero transaction ID and save the transaction key that many Monero wallets can show for an outgoing payment. Send both to support on Telegram at @xswap_to along with your order's transaction ID. Public Monero explorers hide amounts and addresses, so the key helps confirm your payment.
No ID, email or account is requested by xswap.to for this pair. Very occasionally, a partner's automated anti-money-laundering check flags a transaction and holds it until verification is provided. If that happens to your order, support on Telegram at @xswap_to can explain what is needed.
