Swap ETH to ETH in three steps without creating an account. You see an estimated amount before you send, the exchange runs automatically once your deposit confirms, and the ETH goes straight to the wallet address you enter.
Enter the amount of Ethereum (Base) you want to swap in the widget above. It shows an estimate of the Ethereum you will receive on the Ethereum network at the current floating rate, with the payout network fee already taken into account.
Paste your ETH wallet address and check it twice, because blockchain transfers cannot be reversed. If the coin needs a memo or destination tag, a field for it appears. xswap.to never asks for your private keys.
Confirm the order and send your ETH to the one-time deposit address on the Base network. Once the deposit confirms, the swap runs automatically and the ETH is sent to your wallet. The order page shows every stage.
Swapping Ethereum (Base) (ETH) for Ethereum (ETH) here takes one transfer from your wallet: no exchange account, no balance to deposit and no withdrawal queue. You choose the receiving address, and the ETH goes there once the swap completes.
Rates are floating, so the amount shown is an estimate that can shift slightly while your Ethereum (Base) deposit confirms on Base. The payout is sent on Ethereum, so check that your Ethereum address belongs to that network before you confirm.
Refreshed hourly. The widget shows the live estimate.
1 ETH
≈
0.9759495 ETH
At the latest hourly update, 1 ETH converts to about 0.9759495 ETH. The figure comes from the floating rate and already allows for the payout network fee. Rates move, so the widget recalculates the estimate when you enter your own amount, and no account or registration is needed to swap.
Approximate exchange rates between these assets, refreshed hourly
As of Nov 10, 2026 19:03 UTC, 1 ETH is worth about $1,997.12 and 1 ETH about $1,992.85, so 1 ETH converts to roughly 0.97595 ETH. These figures move with the market, and the widget shows the live estimate before you confirm.
Leaving Base for Ethereum mainnet takes one transfer from you: send native ETH on Base to a one-time deposit address, and native ETH arrives on Ethereum at your own 0x address, with no account and no ID upload to start. People move ETH from Base to Ethereum when an exchange account or a mainnet app needs it, or when they would rather not run a withdrawal through Base's standard bridge themselves.
Base, a layer 2 network that Coinbase incubated on top of Ethereum, shares its coin and address format with mainnet: ETH is native on each, an ordinary wallet has the same 0x address on both, and no memo is needed. They are still separate chains, so this is a cross-chain swap. Unlike a withdrawal through Base's standard bridge, which has to be proved and then finalized on Ethereum, the payout here is an ordinary mainnet transfer to your address.
Gas on your side is paid on Base and is usually small, while the Ethereum network fee for sending your ETH is deducted in the floating-rate estimate. That mainnet fee is normally the bigger of the two, so it weighs more on a small swap. The final amount can still shift slightly before your Base deposit confirms. After that, timing depends on the exchange step and on Ethereum, which adds a block every 12 seconds. Your order page lists the deposit and payout transaction IDs.
From live exchange data, refreshed hourly.
| You send | You receive | |
|---|---|---|
| Asset | Ethereum (Base) (ETH) | Ethereum (ETH) |
| Network | Base | Ethereum |
| Type | Native coin | Native coin |
| Memo / tag | Not needed | Not needed |
| Network fee (checked Nov 7, 2026) | ≈ 0.0000028 ETH | ≈ 0.00012 ETH |
| Route | Cross-chain: Base to Ethereum | |
| Rate | Floating, estimate shown before you send | |
| Minimum to send | 0.000127 ETH | |
| Account / ID | Not needed to start a swap | |
Mainly to skip the bridge's withdrawal steps. A standard withdrawal from Base has to be proved on Ethereum, wait out a finalization window and then be finalized, with mainnet gas paid for both Ethereum transactions. Here you make one transfer on Base and the ETH arrives as a normal mainnet payout once the deposit confirms and the exchange step completes.
For an ordinary wallet it is, because the same key controls the same 0x address on both networks. The balances are separate, so ETH held on Base does not appear in your mainnet balance until a swap or withdrawal moves value across. Multisigs and other contract wallets are different, since one deployed on Base may not exist at that address on Ethereum.
The payout is a mainnet transaction, and Ethereum gas usually costs much more than a transaction on Base. That fee is taken from the estimate, while your own Base gas is paid separately from your wallet. On a small swap the mainnet fee is a bigger share of what you send, so check the estimate first.
No, an empty mainnet address can receive the payout, since its network fee is already taken from the estimate. The ETH you do need sits on Base, to pay gas for the deposit. Once the payout lands, that mainnet ETH also covers gas for your next Ethereum transaction.
Neither is needed to start: you enter the amount and an Ethereum address, then send the deposit, with no account and no ID upload. In rare cases the exchange partner's compliance check can pause a swap and ask for verification. If that happens, support on Telegram at @xswap_to explains what to do next.
The order page shows each status, from waiting for deposit to finished, and the Track Order page keeps recent orders saved in your browser. Use the transaction IDs to look up the deposit on a Base block explorer and the payout on Etherscan. If a stage stops moving, send those IDs to support on Telegram at @xswap_to.
